Aircraft grade - Mil spec 4130 chrome moly tubing (used throughout construction)

Chassis is assembled and constructed on a jig fixtured table to provide proper Alignment and containment through the welding process.

Chassis is heli arc welded by a professional welder, who welds each chassis in a special rotational process to minimize heat build up.

Chassis is welded with a special low heat "deep penetration" welding process

Chassis meets SFI spec's 2.5b, this meets 7.50 & quicker spec's and spec's as fast as 6.30.

Chassis is "engineered and designed to the "absolute highest quality standards".

MOTOR PLATES

1/4" 6061 T-6 aluminum CNC profiled & cut full mid motor plate.

STEERING

"New Advanced" narrow stance a-arms with tight turning radius.

Streamline aero tube a-arms "Large" upper & lower!

Stiletto 4130 chrome-moly spindles

4130 chrome-moly spindle arms

4130 chrome moly tie rods

Special offset steering heim washers

Stilleto Billet aluminum rack & pinion

Indy Type Steering Wheel

Lightweight steering shafts

Steering shaft "Safety Frontal Impact" blow back mount

Steering shaft idler bearing

Steering shaft in dash nylon idler washer.

BODY & INTERIOR

Custom aero dynamic body built out of 5052 -.040 aircraft grade aluminum.

Custom cut and fitted by professionals

Body has built-in lower ground effects lip.

MR 5000 custom molded windscreen.

Mil-spec dzus fasteners and springs.

Custom molded fiberglass aerodynamic nose piece.

Custom molded fiberglass seat with all seat belt cut outs.

Custom aluminum fitted floor pan.

Custom aluminum fitted firewall.

Custom aluminum fitted leg protection plate.

Custom aluminum fitted ignition component tray.

"NEW" custom aluminum multi level (wrap around) dash w/gauge cut outs.

"NEW" custom aluminum over lapping removable dash cover.

STANDARD CHASSIS MOUNTS & TABS

Dual Battery Nose mount

Battery lower retainer straps

Battery and main electrical chassis ground

Battery charging lug mount

Master cut off switch mount

Parachute cable mount

Parachute lever and mount

Parachute mount

5 gallon clear "heavy duty' poly fuel cell "Custom Built"

Custom fuel cell filler neck & cap

Steel fuel cell tray and aluminum strap

Fuel cell cover strap mounts

Fuel Cell "Safety" rollover valve & fittings

Fuel cell light mount

Fuel ell light switch mounts

Adjustable gas and brake pedal mounts

Throttle cable mount

Shifter cable

Seat belt mounts

Roll cage exit handles

Lower seat belt hooks

Master cylinder mount

Brake line mounting tab

Brake rod

Cable hole chassis covers

Ignition tray mounts

Blow shield mounts

Aluminum engraved custom blow shield

Dash mounts

Upper & lower mid motor plate mounts

Radiator mounts

Transmission cooler mounts

Recovery tank mounting plate tabs

Lightweight dzus tabs

Engine saddles for front motor plate

Additional ground tabs throughout

Tie strap tubing throughout chassis

REAR END SUSPENSION:

9" Fabricated sheet metal housing

1/4" face plate to insure proper alignment to center section

Internally gusseted

Jig fixtured and time scheduled welding process to minimize heat build up

Lamb symmetrical housing ends

Fill and gear inspection cap and bung

Drain plug and exhaust pressure vent

1/8" 4130 chrome-moly 4 link brackets with support plates on housing

1/8" 4130 chrome-moly front 4 link brackets with support plates

1 1/4" .095 4130 chrome-moly upper 4 link bars

1 1/4" .095 4130 chrome-moly lower x link with adjustable slider tubes with an "engineered" correct a-frame with all the correct geometry and angle necessary for maximum traction!

4130 chrome-moly heim joints

Mono adjustable racing shock & spring.

Dual battery cable kit

MSD Digital 7  ignition control box

K&R, Mega 450 or Dedenbear L-2 Lightening

Choice between Autometer gauges or Racepak replay digital dash

Gauges= tach w/recall, oil press, water temp, volt and trans temp

Trans brake button with cord

Burn out button with cord

Bump down button with cord

Fuel cell light

Battery charging clip in kit

DRIVELINE:

Mark Williams  9" aluminum case, std gear, 40 spline spool & yoke

WHEELS & TIRES:

Spinwerks 16" x 16" wheels & Hoosier tires

SHIFTER:

B&M Pro Bandit or Outlaw electric shifter

DRIVE SHAFT:

Mild steel drive shaft, u-joints & billet trans yoke

U-bolt kit

Hood Scoop & Accessories:

Hood scoop

Undercover 3" scoop pan

Undercover carb base plate to scoop pan mounting kit

Throttle return spring kit

Hans Fuestel  655 cu. in. Chevy Big Block All Aluminum. Dual Carb,  3 - Stages Nitrous,  Abruzzi Transmission,  Hughes Converter.  1200 H.P.

Best ET... 6.48 @ 210 MPH.

(HOME)